Forum Replies Created
- Pat KKeymasterOctober 23, 2020 at 8:33 amPost count: 1508Pat KKeymasterOctober 22, 2020 at 5:34 amPost count: 1508
What a tease….only a couple booty shots.
How do I get on your OF IG page for all the good stuff???
We will build it if it comes.Pat KKeymasterOctober 22, 2020 at 5:30 amPost count: 1508Pat KKeymasterOctober 22, 2020 at 5:26 amPost count: 1508Pat KKeymasterOctober 22, 2020 at 5:24 amPost count: 1508Pat KKeymasterOctober 22, 2020 at 5:22 amPost count: 1508
Like I said before, your skill package over the last couple of years has increased greatly…..😲😲😂😂😂
Have fun out there Emily!!!!!
Lots of pics please!!!
We will build it if it comes.Pat KKeymasterOctober 22, 2020 at 5:17 amPost count: 1508
lots of stories already ! too slow to download photos here. Shakedown at the boarder ! Damn! Took everything out of the bus! Never had it like that before….but they didn’t find it ! hahaha ! Fuck yea !
I imagine after crossing like that is extra relaxing on that beach right now….😎😎😎
We will build it if it comes.Pat KKeymasterOctober 22, 2020 at 5:15 amPost count: 1508
Knocked out one last small repair on the long side near the b pillar yesterday.
Started on driver side seat belt mount repairs yesterday as well.
Patched the bulk head first.
Small section of the seat pedestal to start off last night.
Sandblasted the backside of the mount plate and burned it in.
Lower section of seal channel to finish off this repair.
Fitting the driver side section of the cargo floor now.
We will build it if it comes.Pat KKeymasterOctober 21, 2020 at 8:37 amPost count: 1508
We’re tag teaming you in the dirty shop today Bubby…..hope you enjoy it…😘😘😜😜
JJ is back in action!!!! Knocking out pass side front fender well/ b pillar/ bulkhead work.
I fabrocated a bulk head section and a closing panel to finish up the drivers side front fender well.
We had a couple of funky green closing panels for the front fender wells, but they were a bit short for what we need.
Drivers front fender well is all back together.
We will build it if it comes.Pat KKeymasterOctober 20, 2020 at 11:48 amPost count: 1508Pat KKeymasterOctober 20, 2020 at 11:44 amPost count: 1508Pat KKeymasterOctober 19, 2020 at 3:05 pmPost count: 1508
Mocked up drivers side inner rocker and rear top hat section to start last nights shift. Burned those in.
Outriggers, jack points, lower b pillar, and long side support lower section were next.
Started fitting long side outer.
Made up a small patch section for the front inner lower section of the driver rear fender well.
Just finished tacking the long side into its new home. Really happy with the fit!!!
We will build it if it comes.Pat KKeymasterOctober 16, 2020 at 1:50 pmPost count: 1508Pat KKeymasterOctober 15, 2020 at 1:48 pmPost count: 1508Pat KKeymasterOctober 15, 2020 at 1:22 pmPost count: 1508Pat KKeymasterOctober 15, 2020 at 1:02 pmPost count: 1508
Last nights progress…started by fabing a couple repair sections, one for the center section of the bulk head and one for the inner section of the pass side frame.There was no way to slip the front cargo floor support in place without sectioning it. Cut it in three places, slipped each of them in their spots and welded it back together and to the frame.
Front center section needed a small adjustment to the flanges to fit.
Front heat tube section needed a few repairs.
Slipped all the heat tube sections and the center section into place and welded them up.
Inner rockers and a small frame repair up next.
We will build it if it comes.Pat KKeymasterOctober 14, 2020 at 1:22 pmPost count: 1508Pat KKeymasterOctober 13, 2020 at 10:32 amPost count: 1508
Yup…. fixed all the rusty spots along the edges of the dogleg lips at the floor, a pillars, and the inner valance.
Had to cut the pin to get the ebrake handle out. Heat and some love from the air hammer to get the remains out of the handle.
I was able to drill and tap the broken bolt out of the shifter mount. Front floor install is next up.
We will build it if it comes.Pat KKeymasterOctober 10, 2020 at 9:31 amPost count: 1508
More progress pics….. We decided to add some detail to the wheels.
We’re going to polish the top of the ribs on the running board.
Shorts center caps up front, talls for the rear.
Stacked and stuffed the motor.
Installed the last seal for the sunroof!!!
Laid down 2 layers of Home Depot “sound deadening” everywhere I could.
Started installing some of the gold bits also.
We will build it if it comes.