- BBWBParticipantSeptember 9, 2019 at 6:09 pmPost count: 800
How can you get it to shine more than that? Awesome!
I'm at the age where "fuck off", "fuck you", and "fuck it" answer most questions.WAY2COOLParticipantSeptember 9, 2019 at 7:09 pmPost count: 192
Beautiful work JJ .
Top marks on your craftsmanship with this quickie
Test Pilot @ Submarine AirwaysColeBModeratorSeptember 9, 2019 at 8:16 pmPost count: 1502
Wowowowoowwo looks great in the sun! Drive this thing out Friday!;)John JonesKeymasterSeptember 12, 2019 at 9:14 amPost count: 6326
It looks nice!!!! Real nice…. Been working on it daily.. and going to till we get her done!!!!! 😎 I painted some parts and shit and Pats been installing parts.. will continue on!!! We ordered seals yesterday!….Pat KKeymasterSeptember 12, 2019 at 2:49 pmPost count: 1270
Tail light hold down brackets were missing so I made a pair.
Tail lights, reflectors, and engine bay wiring all taken care of. JJ wanted the decklid pulled off to do a little bit more buffing.
Wet sanded & buffed gas door. Lock mech cleaned/lubed. Couple more small things off the list.
Cleaned up break/license light. Need seals and lenses for both. Would you like to source an OG break light lens or run repop?
We will build it if it comes.kevinbParticipantSeptember 12, 2019 at 10:53 pmPost count: 41
Thanks to Mark L we have seals and lenses coming for the brake light/license light.ColeBModeratorSeptember 12, 2019 at 11:58 pmPost count: 1502
Remind me to give you guys the starter button and these reduction boxes this weekendJohn JonesKeymasterSeptember 16, 2019 at 6:25 pmPost count: 6326
We got our parts from the warehouse!!! I’m back from a killer road trip and ready to get back to it… I got started in building a pod to install!!!!
We need to come up with another high/ lo beam screw terminal foot switch… I found a fuse block that will do the job.
I ohmed everything out and cleaned everything up and cut a new seal for the pod and got them super rusty screws freed up, blasted and painted…
Look at that shine on them Gates!!!! That out next project in the reflection. 😎John JonesKeymasterSeptember 16, 2019 at 6:29 pmPost count: 6326
Pats started on the door frames……
My old race towel from when we had an rc track here… 😎Pat KKeymasterSeptember 17, 2019 at 5:08 amPost count: 1270
Made good progress on this yesterday. Finished pulling all of the wiring harnesses to their locations.
Modified domelight harness from a bus to a single cab. Domelight installed.
Looks like we need to source 3 special clips to secure the dome light wire to the pinch weld seam along the back of the cab.
Passenger door window mostly assembled, need to order a couple of small bits to finish it up but that won’t hold up install.
Rounded up parts that need to be sent out for chrome.
Semaphores sanded and prepped for paint.
We will build it if it comes.John JonesKeymasterSeptember 17, 2019 at 6:48 amPost count: 6326
Pod is going in today!!!! Some glass is going in today also… 😎 gonna be a good week for this truck… 😎John JonesKeymasterSeptember 17, 2019 at 7:16 amPost count: 6326
Oh….. I haven’t seen a wiper motor or shafts or rods for the shafts….Pat KKeymasterSeptember 17, 2019 at 10:26 amPost count: 1270
I was chasing threads on the emblem yesterday and one broke of studs snapped off.
Welded a new one on. Body working the front side. Respray later today
JJ is knocking out pod assembly. Looking good!
Pass door window in. Front and rear window seals on, ready to go in.
We will build it if it comes.John JonesKeymasterSeptember 18, 2019 at 5:27 amPost count: 6326
Kick ass day yesterday….. all the glass is in…. door frames in…. pod assembled and wired in.. Franz located my wiper stuff… so I will get that in today also!! I’m about to repaint that emblem…. I think we will get onto those reducs and check shit out and start prepping for trans assy!!!!! 😎 The beam already looks rebuilt.. It’s just gonna slide back in there….. 😎 I’m gonna start putting pedals together today too….. 😎
Those correct tail lights look awesome.. and those late one’s we took out will look really good in the Pamper… 8-0Pat KKeymasterSeptember 18, 2019 at 5:55 pmPost count: 1270
JJ kicked me out the dirty shop. Couple pics from the drive over.
Tearing reduxs down.
We will build it if it comes.mtnbusParticipantSeptember 18, 2019 at 6:07 pmPost count: 1033
Lookin so good !
hell yea! you guys are the best !Pat KKeymasterSeptember 19, 2019 at 12:04 pmPost count: 1270
Finished redux tear down this morning. Rounded up what needed blasting.
Going to prep everything for paint next.
We will build it if it comes.Pat KKeymasterSeptember 19, 2019 at 5:28 pmPost count: 1270
Epoxy sealed axle tubes in the sweet spots you can’t reach with just one session.
Sealed and painted. Trans assy tomorrow.
We will build it if it comes.
- You must be logged in to reply to this topic.