Parkway projects

[russ]

#58562

damn quick and easy and now a bumpber will stay on

looks great

[Franz]

#58621

We installed some Burley 93o axles on Will’s doka today. Super cool truck. Factory tube, winch and skid plate too.

Ready to go.

[John Jones]

#58623

Sweet!!!!   Great seeing this back together and useful…  😎  and you hired the shop to help?  Good move… Now, where’s my money! 😎

All work and no play makes JJ a dull boy🤣
Keeping a lid on it😎
Attitude is everything 🤔

[gianni]

#58641

Franz wrote:

We installed some Burley 93o axles on Will’s doka today. Super cool truck. Factory tube, winch and skid plate too. Ready to go.

Woohoo! That was so quick! Will has been missing this thing so much..

[Pat K]

#58642

Sanded and painted the rear bumper mount repairs on this ‘65 earlier today.

We will build it if it comes.

[Willy]

#58646

Franz wrote:

We installed some Burley 93o axles on Will’s doka today. Super cool truck. Factory tube, winch and skid plate too.

Ready to go.

 

DAMN! Looks like that bearing cage might be finished… I’m sure the 930s will be quite a bit more tough. Thanks guys, I’m stoked to have my workhorse back in action. I’ll be by this week to grab it and settle up.

[Audrey]

#58664

The Doka is back in action!!!!

Kill em with Kindness 😎

[Audrey]

#58665

Engine is back in on this ‘65! Sounds good!

Kill em with Kindness 😎

[Franz]

#58683

This Fontana grey 65 is all cleaned up and ready to go.

Straitened out the rear fenders and bumper. Replaced a bracket, both uprights and support tubes with originals. New  bumper grommets too.

Wolfsburg West tarboard kit and muffler make it look fresh.

Notice how nice the notches and tabs on the pulley are? Low mileage. Original everything, pump, distributor and carb.

 

[Willy]

#58694

Such a sweet car

[Franz]

#58702

Axle seal, engine oil change/filter, and brake adjustment for Jesse.

I think the axle leak may have been the fill plug leaking as oil is flinging on to it. The tapered pipe threads allow the plug to go deeper than usual. I wrapped it with Teflon tape to hopefully stay dry. You’ll want to keep and eye on it…I did the axle seal kit anyways and used silicone to make double sure. Power washed the oiled down wheel for you too. All clean.

And Jesse you were right about the main jets. I put the exhaust sniffer on it and it was a little rich on the top end. Probably perfect for sea level…. So, I’m going to change them for a size smaller unless you’re planning a trip west anytime soon?

 

[68tintop]

#58704

Sounds good Franz. Change those jets and thanks for fixing that axle seal. Hope to see u guys on Saturday. What time does the race start

[Pat K]

#58707

^^^ 8am Sat, 9am Sun.

http://chcaracing.com/fans/race-weekend-information/

We will build it if it comes.

[John Jones]

#58712

Oh man… sounds like a few of us are going up!!   I’m ready to roll at noonish

All work and no play makes JJ a dull boy🤣
Keeping a lid on it😎
Attitude is everything 🤔

[Franz]

#58778

Working on Rick’s 76 super vert today. Installed a brosal/solex 30/31 carb and empi lowering struts.

The 10 spline lug bolts had me frustrated. I welded 10m nut to the heads so that I could get them off. Also had to cut the hood handle off to adjust the latch mech pull cable.

[Author]

Posts