Pat KKeymasterMarch 2, 2021 at 4:27 pmPost count: 1790
Ebrake handle needs to come out for floor fit.
We will build it if it comes.Pat KKeymasterMarch 2, 2021 at 6:45 pmPost count: 1790
BFG’s!!!! Lookin tuff!
We will build it if it comes.Pat KKeymasterMarch 3, 2021 at 7:05 amPost count: 1790
Couple of hours into my day already. Heat was not enough to get the pin out of the ebrake. Had to cut the pin as usual.
Center safari tab in, fitting outers now.
We will build it if it comes.buddyParticipantMarch 3, 2021 at 11:42 amPost count: 88Pat KKeymasterMarch 3, 2021 at 12:23 pmPost count: 1790
JJ finished straightening bumper blades and fitting new over riders/towel bars. He is out in the blast booth now.
I finished welding safari tabs. The screw on dash tabs will be done after seal install.
Knocked out front floor fit. Decided to seal/ paint the bottom side before install.
We will build it if it comes.Pat KKeymasterMarch 4, 2021 at 4:58 amPost count: 1790
While sealer was drying I started piecing the engine bay back together. Side tray fit and welded. Batt tray going in this morning.
Sprayed the floor bottom side Hanover sealer gray. Ready for install today.
We will build it if it comes.John JonesKeymasterMarch 4, 2021 at 7:16 amPost count: 7465
Bumper full mock up.Pat KKeymasterMarch 4, 2021 at 10:09 amPost count: 1790
All the bits for the engine bay/fender well repairs are burned in and welds dressed!
Ready to start welding the front floor in.
We will build it if it comes.Pat KKeymasterMarch 4, 2021 at 6:00 pmPost count: 1790
The Jones’ body working bumper bits today.
I was able to get the floor about 50% welded before the end of my day. I’ll have it finished up tomorrow along with the heater tube going back in.
We will build it if it comes.FranzKeymasterMarch 4, 2021 at 9:05 pmPost count: 4001
The pre-painted floor looks badass from the bottom side!Pat KKeymasterMarch 5, 2021 at 7:15 amPost count: 1790
Making good progress this morning. Front floor burned in. Fabed a small section of door seal channel for the driver side also.
Grind welds then install heat tube next. Bottom side sneaky peaky.
We will build it if it comes.Pat KKeymasterMarch 5, 2021 at 12:47 pmPost count: 1790
Floor and heat tube install 97% done. Just a bit to finish off on the bottom side.
Darn near done with metal work. Just the treasure chest rocker to go!!! Back at it Monday…😎😎😎
We will build it if it comes.BBWBParticipantMarch 5, 2021 at 1:07 pmPost count: 929
I gotta say, nothing looks better than a freshly installed floor. Nice work Pat.
I'm at the age where "fuck off", "fuck you", and "fuck it" answer most questions.Pat KKeymasterMarch 5, 2021 at 5:55 pmPost count: 1790
JJ finished body working bumpers and laid down spray poly today.
He also painted the wheels.
We will build it if it comes.Pat KKeymasterMarch 8, 2021 at 8:19 amPost count: 1790
JJs sanding bumpers for paint this morning.
Cargo rocker was full of dirt!!
Major sections chopped out, just little bits to dissect.
We will build it if it comes.Audrey JonesModeratorMarch 8, 2021 at 11:47 amPost count: 333
Pat’s getting that area all cleaned up before the new rocker goes in 👍🏻
JJs doin what he loves to do… sanding!!!😉
- You must be logged in to reply to this topic.