Home › Forums › KCW Completed Projects › Pauls 60 Single cab

Viewing 0 posts
Viewing 15 posts - 466 through 480 (of 608 total)
Previous 1 2 3 … 31 32 33 … 39 40 41 Next
  • Author
    Posts
  • Franz
    Participant
    February 27, 2018 at 8:25 am
    Post count: 5403
    #9694

    Cleaned and lubed all the cables/tubes yesterday. They usually have old grease and sand slurry in them that makes for crunchy operation. These will glide nice and smooth. I wish it were as easy to fix nerves in the human body.

    All new cables and linkages. Not a bunch of half-life stuff.

    DSC00534DSC00526

    Peet tackled pedal assembly and some engine stuff.

    DSC00532DSC00530

    Rustabus
    Participant
    February 27, 2018 at 10:05 pm
    Post count: 3393
    #9714

    That shit matters!!!! Taking the time to clean out the tubes and get nice greased cables in makes a Bus drive soooooo smooth!!!! 🙂 🙂 🙂

    John Jones
    Moderator
    February 28, 2018 at 6:18 am
    Post count: 13880
    #9719

    Guys are killing this thing…  😎  About time to feed them some more painted parts…  😎  Your parts table is getting cleared off!!!! 😎

    DSCF5955DSCF5956DSCF5957

    Been a wild ride, but it got me here 😎

    Franz
    Participant
    February 28, 2018 at 8:55 am
    Post count: 5403
    #9735

    Hooking stuff up. Steering, clutch, e-brake, gear oil, carb rebuild/re-jet, battery/cables, new clutch, new bosch coil, new fuel pump, new bus muffler, fan belt, etc.

    I think we are green light for a mechanical test drive today.

    DSC00554
    DSC00552
    DSC00557

    DSC00544DSC00542DSC00546

    russ
    Participant
    February 28, 2018 at 11:05 am
    Post count: 147
    #9738

    killing it

    I want to see this thing move on it’s own power now

    keep it up

    Volksman
    Participant
    February 28, 2018 at 12:17 pm
    Post count: 60
    #9741

    Such a cool build! I am also excited to see the sucker up and running.

    John Jones
    Moderator
    February 28, 2018 at 6:00 pm
    Post count: 13880
    #9751

    Pat drove it in and out today…. It is alive again!!!!!!!

    DSCF5984DSCF5983DSCF5985

    Been a wild ride, but it got me here 😎

    Jdawg
    Participant
    February 28, 2018 at 6:16 pm
    Post count: 478
    #9754

    Amazing!!! Is that a T34 in the background?

    Franz
    Participant
    February 28, 2018 at 7:22 pm
    Post count: 5403
    #9756
    Jdawg
    Participant
    March 1, 2018 at 3:57 am
    Post count: 478
    #9760

    Hell yeah!

    Paul Sexton
    Participant
    March 1, 2018 at 4:19 am
    Post count: 88
    #9762

    Hellz yeah!! Looks so good rolling on those tall tires!! Bet I’ve watched this 50 times. Thanks for the update Franz.

    Franz
    Participant
    March 1, 2018 at 9:27 am
    Post count: 5403
    #9768

    Drove perfect too. Totally stoked. Ready for removable and finish work.

    I ordered a Clara grey interior panel board kit yesterday.

    Pat K
    Participant
    March 1, 2018 at 3:48 pm
    Post count: 2933
    #9783

    Starting to work over some removables on this rig now that Unks vert is clean shop bound.

    We will build it if it comes.

    John Jones
    Moderator
    March 1, 2018 at 7:12 pm
    Post count: 13880
    #9791

    we decided to ditch your apron and get you a new one…  We will get the front doors and engine lid prepped, hung, in the b0oth, epoxy sealed and painted yellow tomorrow….  Then start getting parts painted!!!!!  Gates and teasure chest door blasted and polied also…  2 more weeks to try and have all the paint work done for this….  😎

     

    Been a wild ride, but it got me here 😎

    Pat K
    Participant
    March 2, 2018 at 11:13 am
    Post count: 2933
    #9822

    Doors , lid and misc parts just went in the booth for a yella paint session.

    We will build it if it comes.

  • Author
    Posts
Viewing 15 posts - 466 through 480 (of 608 total)
Previous 1 2 3 … 31 32 33 … 39 40 41 Next
  • You must be logged in to reply to this topic.