- RustabusParticipantSeptember 27, 2017 at 6:56 pmPost count: 1844
Damn! Love the KCW Spa treatment!!!!!!!!!!JdawgParticipantSeptember 27, 2017 at 7:26 pmPost count: 447
right??? I guess I’m moving to Grand Junction so I can be closer. 😎RedParticipantSeptember 27, 2017 at 7:34 pmPost count: 14
I did my normal rounds on the engine, then went over and tidy’d up a few things.
<iframe id=”player_1″ src=”https://www.youtube.com/embed/qu3351-j0oc?feature=oembed&enablejsapi=1&wmode=opaque” name=”fitvid0″ width=”300″ height=”150″ frameborder=”0″ allowfullscreen=”allowfullscreen” data-mce-fragment=”1″></iframe>
- nut-zert on the coil
- re-routed a few wires and took off any plastic collars on connections
- swapped faulty electronic ignition for points
- increased idle jet to 55
- measure/marked true TDC
- adjusted advance base line and limit to 11-29 degrees
- hooked-up and adjusted choke
- removed the pre-heat flap from the air cleaner
Welded the spring brace back to the skin and touched up with some anthracite paint.
Wow this thing has never run this clean, Justin is so stoked! Maybe now I can get a ride.JdawgParticipantSeptember 27, 2017 at 7:41 pmPost count: 447
Wow this thing has never run this clean, Justin is so stoked! Now I need my own VW.
fixed it for you. 😆JdawgParticipantSeptember 27, 2017 at 7:49 pmPost count: 447
I’ve watched the video Franz posted about 8,432 times! Fuckin puuuuuuumped!RedParticipantSeptember 27, 2017 at 9:46 pmPost count: 14
Amen to that! One project at a time though….. 😐RedParticipantSeptember 27, 2017 at 9:47 pmPost count: 14
Guess we’ll watch it a few more times tomorrow at work!LolJohn JonesKeymasterSeptember 28, 2017 at 6:27 amPost count: 6326
Oldmann is sitting solidly on the ground… Franz did TONS of little things to your car.. I’ll let him fill ya in though…FranzKeymasterSeptember 28, 2017 at 8:48 amPost count: 3363
Yeah man, all over it. I did some shimming on the link pins, installed a couple grease zerks, cut the shock dust covers, flipped the shocks, changed fuel hoses. Removed the hard start relay, then fixed the root of the problem. Corroded ignition switch contacts, battery cable, and starter.
The glass fuel filter and this location was no bueno. Surely cause some vapor lock issues. I put a plastic filter in the engine bay after the fuel pump.FranzKeymasterSeptember 28, 2017 at 8:50 amPost count: 3363
The rear suspension had bump stops. I took them off and noticed that I could get the spring plate to bottom out on some rough stuff. I’m going to notch the plates today.FranzKeymasterSeptember 28, 2017 at 8:53 amPost count: 3363
After that I think I’ll have it pretty much dialed mechanically. I’m going to come in way under budget, and still have tomorrow to do stuff. Anything else you can think of? Paint/detail the wheels? I could pull the fender guards like we talked about. But not sure I’ll have enough time before the weekend to do correct paint repairs. You’re still coming this weekend?
JdawgParticipantSeptember 28, 2017 at 9:00 amPost count: 447
- This reply was modified 2 years ago by Franz.
dang man you’re killing it!…what is the hard start relay? yeah that fule filter was my dumb mistake…the vapor lock thing totally makes since now.JdawgParticipantSeptember 28, 2017 at 9:11 amPost count: 447
actually, I’m coming next weekend…sorry if I made it sound like it was this weekend, I meant the first full weekend of October.
as far as other stuff goes…how about rear shocks? did you figure out what was puking fluid on the tranny? i replaced one of the boots but the other one was old…maybe replace those? the horn has never worked that would be cool to have working. are the brakes good to go? I redid them but wanted you to make sure they were adjusted and stuff. the gravel guards being gone would really cool…if you can make em go away without it being too obvious they were there go for it. i think the speedo could use some love, the odo doesn’t work and one of the idiot lights doesn’t idiot lol.
if you have the time to keep dialing and we still have budget…dial away.JdawgParticipantSeptember 28, 2017 at 9:15 amPost count: 447
you know…………I’ve always wanted some Porsche alloys….is there a way to re-drill drums and have both bolt patterns? JJ mentioned that he had some OG bumpers…what about something like that?
I’ve seen you guys do some bitchin headlights…the ones on there are kinda cheesy repops….
all just thoughts…what do you think?FranzKeymasterSeptember 28, 2017 at 3:12 pmPost count: 3363
Yeah I adjusted the brakes and pedal stops. I noticed that the brake fluid was dark. I replaced with new, and bleed out.
Cool. We have time to do some stuff. I got you.
OG exhaust clamp are a better fit.JdawgParticipantSeptember 28, 2017 at 3:32 pmPost count: 447
bad ass man!!! again THANK YOU for what you’re doing! I cant explain how excited and happy I am.John JonesKeymasterSeptember 29, 2017 at 7:25 amPost count: 6326
Looks like some chrome fender guards came off last night.. 😉 😉 I bet Justin is all dialed in today!!!!!! Hey….. Next weekend when you come get it… we gotta get that “Roosters” picture…. 😉 😉 😉 Remember.. You guys can stay at the compound…. 😉 No hotels.. Pat and Franz might be racing BMX next weekend.. it’s the Stat Champs…. 😉BBWBParticipantSeptember 29, 2017 at 7:55 amPost count: 800
I’d like to be in the “Thursday Club” someday. Kinda’ out of my reach financially, so “Parkway Project” would be more like it. 😆
I'm at the age where "fuck off", "fuck you", and "fuck it" answer most questions.JdawgParticipantSeptember 29, 2017 at 7:57 amPost count: 447
- You must be logged in to reply to this topic.